Search found 10 matches

by blueblazer
Tue Jun 02, 2015 9:32 am
Forum: MegaShift Transmission Application
Topic: Stop light surge
Replies: 2
Views: 7464

Re: Stop light surge

No data log. Very sure it is transmission related. Feels just like my buddy's Dodge did when his OEM ECU went bad and was trying to lockup his torque converter at idle. Totally different engine and transmission than my 350 and 4L60E but the exact same feeling. Hoping someone else has felt this befor...
by blueblazer
Tue Jun 02, 2015 6:25 am
Forum: MegaShift Transmission Application
Topic: Stop light surge
Replies: 2
Views: 7464

Stop light surge

4L60E Trying to tune out my slight surge at stop lights and such. I've got TPS reading 0% and the brake signal. Idle is about 650-700 depending on engine temp. When I come to a stop, the truck pulls a little as more of a surging than a steady pull. The brakes easily over power it but I feel it happe...
by blueblazer
Tue May 26, 2015 12:34 pm
Forum: MegaShift Transmission Application
Topic: CAN bus 5101
Replies: 9
Views: 12681

Re: CAN bus 5101

I have CAN_Commands set to active on both the MS3x and the Megashift. Should I maybe only have one or the other turned on? Is that maybe what's causing the MS3x to push through a full settings change?
by blueblazer
Tue May 26, 2015 10:16 am
Forum: MegaShift Transmission Application
Topic: CAN bus 5101
Replies: 9
Views: 12681

Re: CAN bus 5101

Understood. If I do that though, once I select the MShift_5101.ini and click okay in project properties window the system restarts and shows a difference report of TS vs controller. The TS is all default values for MSHIFT_5101. So I tell it load from controller and all is good that run. When I turn ...
by blueblazer
Tue May 26, 2015 5:51 am
Forum: MegaShift Transmission Application
Topic: CAN bus 5101
Replies: 9
Views: 12681

Re: CAN bus 5101

You are correct sir, the serial connection is to the MS3x. Tried the MShift.ini and that seems to wipe out my transmission settings. Using the mainController.ini loads all the transmission settings. I'm confused by this a bit as that link to the directions seems to be what you're saying. I've read i...
by blueblazer
Mon May 25, 2015 7:22 pm
Forum: MegaShift Transmission Application
Topic: No gear position
Replies: 2
Views: 5937

Re: No gear position

Still not looking like the system knows if I'm in gear but it runs through the gears when I drive around. I'll post my msq and log tomorrow when I can have my brother run the laptop while I drive. Really happy the CAN is working and the GPIO has enough signals to drive.
by blueblazer
Mon May 25, 2015 7:18 pm
Forum: MegaShift Transmission Application
Topic: CAN bus 5101
Replies: 9
Views: 12681

Re: CAN bus 5101

I figured out the connection problem. Wasn't software, was hardware. Odd error message for a missed solder connection on the 3.0 main board. Couldn't say something like "no signal." Now my only question is, do I reference the GPIO_Mshift_5101.ini that I downloaded or the mainController.ini...
by blueblazer
Mon May 25, 2015 6:25 am
Forum: GPIO Assembly
Topic: MS3x tach signal into GPIO mshift
Replies: 1
Views: 13951

MS3x tach signal into GPIO mshift

Having no luck setting up CAN bus so I'm going to piggyback onto the MS3x. I need to know what, if anything will be needed in modifying the GPIO board to take the tach signal from the MS3x.
by blueblazer
Sun May 24, 2015 1:03 pm
Forum: MegaShift Transmission Application
Topic: CAN bus 5101
Replies: 9
Views: 12681

CAN bus 5101

So... Trying to connect MS3x to GPIO board via CAN. Seems the GPIO_MShift_5101.ini file needs some alternate signature to work as the referenced firmward file when setting up the CAN in MS3x. This is what I understand from the MSExtra forum where they helped me trace my problem to that. Maybe that f...
by blueblazer
Sun May 24, 2015 9:49 am
Forum: MegaShift Transmission Application
Topic: No gear position
Replies: 2
Views: 5937

No gear position

Trying to figure out why I don't show a gear position. The gauge has -1, 0, 1, 2, 3, 4 and only sits at 0 no matter where I move my shift lever. I double checked the wiring between the ecu plug and the trans plug and all my wires match per the wiring schematic. When I set up the basic tune I selecte...