Search found 47 matches

by Rukavina
Thu Sep 28, 2017 8:30 pm
Forum: MegaShift Transmission Application
Topic: Sheriff left town?
Replies: 5
Views: 8637

Re: Sheriff left town?

Last I saw life from him was may 31st. I was having a comm issue around that time and was corresponding with other people and then saw that he did a code revision and that was it.
Not much activity here anymore
by Rukavina
Wed Sep 27, 2017 9:02 pm
Forum: MegaShift Transmission Application
Topic: Anyone in So Cal able to assist with tuning?
Replies: 4
Views: 7768

Re: Anyone in So Cal able to assist with tuning?

The manual says 17-20...I think... are good for serial ground. I would keep it close to the plug on gpio to avoid noise/ground loop issues
Busy with frightdome setup here in vegas but if get some time I will post pics/schematic of how I did it.......
by Rukavina
Sun Sep 24, 2017 9:23 pm
Forum: MegaShift Transmission Application
Topic: Anyone in So Cal able to assist with tuning?
Replies: 4
Views: 7768

Re: Anyone in So Cal able to assist with tuning?

Grab a drac off of a Chevy. I could not get the "oem" gpio vss to work so I made a custom vss circuit but it flip flopped and doubled the input pulse frequency. Then I did the drac mod and it works real good. One of the issues I was having with the custom thing I made is I also run the " cable x " m...
by Rukavina
Sat Aug 26, 2017 9:06 am
Forum: MegaShift Transmission Application
Topic: CAN pass through
Replies: 3
Views: 7275

Re: CAN pass through

Msextra 3.4.2
by Rukavina
Fri Aug 25, 2017 9:53 pm
Forum: MegaShift Transmission Application
Topic: The 4.7 ohm resistor
Replies: 2
Views: 6846

Re: The 4.7 ohm resistor

I believe, depending get on your trans, when at full pressure solenoid is off. As you lower the pressure the valve is on more.... and regardless of pulsewidth as duty increases valve will get hot. Think of pw as hz. If you have a long pw it might go back and forth 10 times at 100%DC. If you have a s...
by Rukavina
Fri Aug 25, 2017 9:40 pm
Forum: MegaShift Transmission Application
Topic: CAN pass through
Replies: 3
Views: 7275

Re: CAN pass through

Yes I run ms2 v3 with gpio board together on canbus
by Rukavina
Fri Jul 28, 2017 9:36 pm
Forum: MegaShift Transmission Application
Topic: Kick down tuning
Replies: 6
Views: 8708

Re: Kick down tuning

I am no expert but grab a datalog...
Also try jumping over to the msextra forum for the microsquirt transmission control section. They might have an idea even though it's not for the gpio board or b&g firmware.
by Rukavina
Fri Jul 28, 2017 5:55 pm
Forum: MegaShift Transmission Application
Topic: Kick down tuning
Replies: 6
Views: 8708

Re: Kick down tuning

DO NOT LOAD THIS TUNE! mine is a 4l80e not a 4l60. I looked at your settings and other than kilometers don't work well with my brain (American) some of what stood out to me was some of your tables. your tps by rpm table is different than mine. I have that table bypassed. granted I am not done tuning...
by Rukavina
Tue Jul 25, 2017 10:57 pm
Forum: MegaShift Transmission Application
Topic: Kick down tuning
Replies: 6
Views: 8708

Re: Kick down tuning

Try increasing shift hysteresis so it has to see a bigger change before shifting again. It sounds like soon as it shifts down it puts engine in a state where tranny wants to shift back up. I read these posts every night on my phone to put me to sleep so I am not at laptop to look at settings. Post y...
by Rukavina
Wed Jul 19, 2017 10:22 pm
Forum: MegaShift Transmission Application
Topic: tps
Replies: 1
Views: 6443

Re: tps

Yes it will work "standalone". I don't remember the details but it does use iss, oss and some engine reference to determine load. It is 0 - 5v ref. Map, tps or maf. An old fashioned firewall mounted map would be easiest if it's a older carburetor engine. 5v in from gpio to map, signal out from map a...