Search found 9 matches

by KamikazeTuner
Sun Nov 18, 2012 7:08 pm
Forum: MegaShift Transmission Application
Topic: Audi 094 4 Speed - Solenoid Output
Replies: 9
Views: 12520

Correction and advice-

Here is a link to that correction I mentioned on my previous post. It is very important if you are running your serial communication out of the AMP connector. See the following link-- http://www.msgpio.com/forums/viewtopic.php?f=9&t=457 Also, it is recommended to cycle the power (off-on) when ma...
by KamikazeTuner
Wed Nov 14, 2012 11:49 pm
Forum: MegaShift Transmission Application
Topic: Audi 094 4 Speed - Solenoid Output
Replies: 9
Views: 12520

Re: Audi 094 4 Speed - Solenoid Output

Got everything working great!! There is some incorrect info on the Build Manual regarding the RX and TX signal. I will start a new thread with my findings, few people will find it in this Audi Transmission thread. Hopefully it will help others going thru a similar dilemma.
by KamikazeTuner
Thu Nov 08, 2012 2:51 am
Forum: MegaShift Transmission Application
Topic: Audi 094 4 Speed - Solenoid Output
Replies: 9
Views: 12520

Re: Audi 094 4 Speed - Solenoid Output

Well, It sort of fixed some of the problem. I gained access to VB2 (SpareOutput 2) But after about 1 hour of playing with it, I have lost all 3 of my inputs. I am getting 4.5Volts out of wires 6, 25 and 26 on the Amp connector, and my TransStim is grounding correctly. Not sure what is going on now. ...
by KamikazeTuner
Wed Nov 07, 2012 6:14 pm
Forum: MegaShift Transmission Application
Topic: Audi 094 4 Speed - Solenoid Output
Replies: 9
Views: 12520

Re: Audi 094 4 Speed - Solenoid Output

Lance, I just noticed a HUGE mistake in my part. When building the board, in particular jumping the 25x2 headers. I accidentally jumped AD1 to VB2 instead of the correct method of AD1 to GPI2. That explains why I an having all these issues with Inputs and Outputs. I will correct it and report back.
by KamikazeTuner
Wed Nov 07, 2012 5:26 pm
Forum: MegaShift Transmission Application
Topic: Audi 094 4 Speed - Solenoid Output
Replies: 9
Views: 12520

Re: Audi 094 4 Speed - Solenoid Output

Lance, As always, Thank you for the quick response. The problem is that when I set Spare 1 and 2 to Clutch outputs, I lose a shift solenoid (3 shifts and 2 clutch) and when I set them all as Shift solenoids, I am still short one shift solenoid. Thanks to the TransStim, I was able to figure out I am ...
by KamikazeTuner
Wed Nov 07, 2012 3:03 am
Forum: MegaShift Transmission Application
Topic: Audi 094 4 Speed - Solenoid Output
Replies: 9
Views: 12520

Audi 094 4 Speed - Solenoid Output

I built my GPIO board to the 4L60E Trans specs as it resembles my Audi 094 trans in general operation. Except that The Audi 094 has 7 solenoids. 4 of them are gear solenoids, 2 are Clutch solenoids, and 1 is a Pressure Control Solenoid. The Pressure control Solenoid is the only one that will need PW...
by KamikazeTuner
Thu Oct 04, 2012 9:59 pm
Forum: GPIO Assembly
Topic: GPIO BOARD CUT to short. TRACES NEEDED!!
Replies: 2
Views: 16180

Re: GPIO BOARD CUT to short. TRACES NEEDED!!

magnamx-5m---Thanks for pointing me in the right direction. I was suspecting a cut trace to D4, and with help from the drawings, I figured it needed a 12V feed. Back up and running!! Thanks again for the help!!! Both boards in the same case is great! I have attached some pics of the progress.
by KamikazeTuner
Wed Oct 03, 2012 1:07 am
Forum: GPIO Assembly
Topic: GPIO BOARD CUT to short. TRACES NEEDED!!
Replies: 2
Views: 16180

GPIO BOARD CUT to short. TRACES NEEDED!!

So, I have a MegaSquirt2 v3.57 and a GPIO/MegaShift. I successfully got them both talking to each other (via CAN). Loaded up with some settings on TunerStudio MS. I purchased the EAS-400 aluminum enclosure to house them together. Nice and compact in one unit (So I thought...). Problem is the Amp Con...
by KamikazeTuner
Tue Sep 25, 2012 11:08 pm
Forum: MegaShift Transmission Application
Topic: Audi 097 4 speed Automatic and MegaShift
Replies: 1
Views: 4929

Audi 097 4 speed Automatic and MegaShift

I have a MS2 v3.57 w/ software (Monitor_v2.905.abs) and I built my GPIO/MegaShift w/ software (Monitor_2202.abs) It is talking to my Laptop and TunerStudio MS is also able to talk to the module. Now I am at the point where I need help! I am using MegaShift to run a 1997 Audi 097 4 Speed Automatic Tr...